Your Cart is Currently Empty
The moving coil principle was chosen as the basis for the design of the IO range of cartridges, as it offers greater linearity in terms of electrical output from the mechanical movements of the stylus than any other system. We investigated moving iron, moving magnet, strain gauge, electret and electrostatic generators, and even took the unusual step of acquiring a Toshiba cartridge that employed light emitting diodes to generate the signal from the groove, but in the end it was felt that the quality of the moving coil system as described by P. G. A. H. Voigt would yield the best overall results.
To ensure that the stored information on the disc is precisely recovered, it is essential that the mechanical movement of the stylus is accurately translated into an electrical signal. Any extraneous excitation arising as a result of vibrations in the cartridge housing must be eliminated.
Therefore in the design of the Audio Note (UK) cartridges considerable attention has been paid to the rigidity and structural integrity of the body, and to ensuring that the adopted mechanical construction stores the absolute minimum of resonant energy, which will degrade the signal derived from the disc being played.
Mechanical integrity of the cartridge body is an aspect of design that has never been adequately dealt with before, and as a result all other cartridges suffer greatly from colourations derived from internal resonances and/or energy stored in their body assemblies.
To achieve the incredible level of mechanical integrity required for the IO cartridges, all aspects of body design were reexamined, to minimise standing waves and eliminate any resonating air pockets within the assembly.
The benefits of getting the mechanical assembly right would be lost if the complete assembly could not be rigidly mounted in the tonearm, hence the incorporation of the largest possible surface mounting area and the provision of up to six (6!) bolts to secure the cartridge to the head shell.
Once the mechanical assembly had been perfected the next area to which particular attention was paid was the magnetic circuit.
From numerous tests carried out on a variety of materials and configurations, it was established that different types of magnetic materials exert a subtle influence on the perceived quality of the final sound.
After further extensive research the optimal magnetic circuit was found to be electromagnetically generated. This, however, requires a separate DC power supply and is very costly to implement. This is exactly the system we implemented in our flagship Moving Coil cartridge – the IO Limited – which offers an unparalleled level of performance. However, for the IO II we chose the next best materials; AlNiCo magnets for the IO II and IO Gold, and for the IO I.
Because of the low impedance and very low output of the IO II, it is essential that the minimum number of electrical connections occur along the wire and that the wire itself is of the highest possible quality. Not surprisingly we chose our custom made Audio Note (UK) 99.99% pure silver wire, and the coil wire extends all the way to the output terminals, avoiding all unnecessary connections.
Cantilever, Material and Design
It is on the design and construction of the cantilever that much of the quality of a cartridge depends. Many materials were investigated, Boron, Beryllium, Sapphire, Diamond and Titanium and all except Titanium were disregarded in the final analysis, due to deficiencies in one or more areas.
It is vitally important for the cantilever and stylus assembly to be as rigid as possible in order to accurately transfer the stylus motion to the coil assembly, without adding any unwanted vibration as a result of flexing or bending.
The optimum cantilever material here was found to be an extra thick walled, slightly tapered Titanium tube, the taper being both outside AND inside, since this affords by far the greatest rigidity.
Another advantage provided by this type of material was the possibility of employing a longer cantilever, which greatly reduces cantilever excursions. This has three main benefits: -
1) It is easier for the stylus to track complex, highly modulated grooves.
2) The resultant smaller coil movement reduces the non-linearity of the magnetic field, so the field will ‘bend’ less.
3) Damping can be reduced, as it becomes easier to control stylus movement.
As mentioned above, damping of the cantilever is extremely critical. Too much and the cartridge will sound dull, as a large amount of the critical energy from the record will be absorbed in the damper instead of reaching the coils, reducing the efficiency of the energy transfer from the record (as vibration energy) to the cartridge (as electrical energy).
Conversely, too little damping will make the cantilever prone to uncontrolled excursions, resulting in unwanted distortions and poor tracking.
Much experimentation led to a precision Butyl rubber damper, offering a wide operating temperature range and minimal hysteresis effects. The tension on the damper is furthermore adjustable, allowing very accurate set-up of each cartridge’s individual suspension.
Finally the assembly is completed with the use of a solid diamond stylus. A heroic degree of effort has been expended finding the best possible solution to this, the most critical interface with the “plastic”. Having been ultimately unsatisfied with the offerings from the various stylus manufacturers around the globe, in 1995 we contracted a company to develop a process which would allow them to cut and polish a perfect, natural octagon to a level of the best surgical instruments used for eye and other fine surgery, on a diamond less than half the size of the closest, readily available option at that time. This remains to the best of our knowledge the finest diamond in use on any cartridge available today.
The improvements over any standard diamonds use in other cartridges can be briefly described as better tracking of high frequencies, lower surface noise, lower record wear, longer stylus life, smaller tip mass and lower tracking force.
The stylus is first ‘pinched’ into place by the cantilever and then glued, using a single component epoxy resin, which needs ‘baking’ for about three hours to harden.
After assembly, each cartridge is subjected to a series of tests, one of which involves a fast dynamic frequency sweep, at high amplitude; this method shows up any undesirable problems in the cartridge. Special test equipment and test records had to be developed for this process, which is exclusive to Audio Note (UK).
All orders are processed within 48 hours from date of order.
We offer Free Ground Shipping on all orders regardless of size.
- If you would like to receive your order quicker you can request Express shipping during Check-Out in the Comments section. Additional charges will apply.
- In-stock items are shipped from our Vancouver warehouse and will reach major Canadian cities in 5-7 business days.
- Items not in stock will either ship from one of our manufacturer partners' warehouses or in rare cases first must be sent to Vancouver and then to you.
- If the expected arrival to you will be more than 7 business days you will be notified by email and at that point you will have the option to proceed or if you cannot wait then order can be cancelled.
We will gladly:
- (a) exchange a product that is not special ordered, or shipped from one of our partner warehouses, for a new product of equal value (product purchased must be unopened)
- (b) exchange a product if it is defective or damaged for the same product
within 15 days after the product has been delivered to you.
Returns for refund are not accepted.
For an exchange, you must notify us by email at email@example.com. We will acknowledge receipt of your email by reply and assist you in returning the product as identified below. Make sure to send and have your return package post marked within the 15 days after the product has been delivered to you.
- Headphones may not be returned or exchanged for any reason, only defective units will be replaced for the same model
- Items that have been opened may not be returned
Notwithstanding the foregoing, you may cancel an order if the product is not delivered to the delivery address on your order form within 30 days of the date your order is accepted.
To cancel, you must notify us by email at firstname.lastname@example.org. We will acknowledge receipt of your email and process the cancellation.
Products returning for exchange must be unused and in their sealed, original factory packaging.
Buyer is responsible for return shipping costs.